Artwork, Lights, Outlets, And A Partially Loaded Walk-In Closet

I modified my thoughts on what I wished to work on yesterday. As an alternative of engaged on the island, I made a decision I wished to attempt to knock off as most of the small objects left on my to-do checklist as attainable. I received’t bore you with each tiny element, however I began off the day with 30 objects on my checklist, and I acquired 14 of them executed, and the fifteenth is in progress. So it was a really productive day! And getting virtually 15 issues knocked off of my checklist felt a lot extra satisfying than simply making an attempt (and probably failing) to get one massive factor executed. I wanted that increase yesterday.

The very first thing I wished to get executed was hanging the photographs and lights above the washer and dryer. I purchased these picture lights (affiliate hyperlink) that come able to be hardwired, however I didn’t wish to put junction containers within the wall. So I made a decision to wire them in order that they are often plugged in as a substitute. Fortunately, that they had a gap within the backplate in order that they could possibly be wired for plugin.

To do this, I bought two of those extension cords from Residence Depot…

After which I used my wire cutters to chop the receptacle finish off of the wire.

Utilizing my utility knife, I separated the three wires.

Subsequent, I recognized the recent wire and the impartial wire. The wires within extension cords are virtually by no means wrapped in black and white, so it’s not fairly as simple to establish which one is scorching and which one is impartial. However all it’s a must to do is take a look at the sheathing on every wire. You’ll discover that the sheathing on one will likely be clean, and the sheathing on the opposite will likely be ribbed going the size of the wire. The ribbed wire is the impartial that connects to the white wire within the gentle fixture. The graceful wire is the recent wire that connects to the black wire within the fixture.

Hopefully you may see what I imply within the picture under. The wire on the underside is the graceful (scorching) wire and the wire on the highest is the impartial (ribbed) wire. You do need to watch out not to concentrate to the areas the place the person sheathings have been lower or torn aside. These torn/lower components can typically be mistaken for the ribbed sheathing, so it’s a must to make sure to ignore these areas.

After which stripped the tip of every wire about 5/8 inch.

And at last, I put the wires by means of the outlet on the backplate of the sunshine, and wired the wire to the sunshine — clean to black, ribbed to white, and floor to floor.

The set up was the identical as it could have been had I hardwired it. I used the identical mounting plate offered. The one distinction is that the wire comes out the underside of the sunshine and runs behind the image.

I actually love these lights. They arrive with a distant, and you may change the colour in addition to the brightness.

I wish to share yet another of my initiatives from yesterday that may be useful for a few of you. I’ve 4 retailers that have been coated over by the closet cupboards, in order that they wanted to be uncovered. Typically, I used field extenders in order that they retailers could be prolonged in order that they’re flush with the again of the cupboards. However on this case, there wasn’t sufficient wire to convey them ahead that a lot. So I needed to get inventive.

I used my Dremel Multi-Max to chop a rectangle that was about 1.25″ bigger than the outlet on either side. After which I used a full protection paintable outlet cowl on the wall.

Then I used 1/4″ wooden, lower to the width I wanted on my desk noticed, and made this dimensional body. The again half suits into the rectangle I lower and sits in opposition to the wall, and the entrance half frames it in order that the lower edges of the cupboard again are hidden.

I put it along with my scorching glue gun, did slightly caulking, after which positioned it into the rectangle cutout and secured it with 5/8″ 18-gauge nails.

After which I painted the entire thing to match the again of the cupboard.

I really like that it’s set again from the cupboard like this. Since this can be a part for hanging garments, I really feel prefer it’s safer having it recessed like that. So it labored out nice!

And as soon as that paint was dry, I may lastly begin bringing stuff in! I didn’t get very far with it, however I did get this part stuffed…

After which I introduced in all of my purses and acquired them organized.

So I’m inching my means in the direction of that end line, slowly however absolutely!

Extra About My Stroll-In Closet/Laundry Room

see all walk-in
closet diy initiatives

learn all walk-in
closet weblog posts

Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and beautify the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do the vast majority of the work on the home on my own. You can learn more about me here.

Trending Merchandise